ClassicXray Home
View Boxes
X-ray Processors
Imaging film
X-ray Cassettes/Screens
Mobile X-ray Barriers
MISC. X-ray Supplies
Contact Us
OptiMax NDT
Industrial X-ray Processor

Quality, Features and Value
The OPTIMAX 2010-NDT is a fully automatic industrial processor, with a variable speed control that allows precise settings from 90 seconds to 10 minutes. The OPTIMAX 2010-NDT provides a state-of-the-art digital display for monitoring and control of developer temperature, dryer heat, replenishment, process time, diagnostic messages, and film volume.

The OPTIMAX 2010-NDT is manufactured by Protec in Germany in compliance with DIN ISO 9001:2000, IEC, TUV, CE, CSA, and UL quality standards. Protec is known world-wide for their simple, reliable, serviceable, and affordable industrial x-ray film processors.

Uncompromising quality
The one-piece casing and the exclusive use of high quality components guarantee the highest degree of reliability.

Best economic efficiency
The integrated stand-by mode reduces your water and energy consumption. The film detection with a micro sensor enables intelligent and economic replenishment depending on the processed film surface. Because of that the OPTIMAX® saves chemicals and provides a constant high quality of your image.

No problem operation, perfect safety
With the simple control panel the tanks can easily be filled during the warm-up cycle, and the developer temperature can be set. Acoustic and visual controls signal the readiness for processing of the next film. The anti-crystallization and anti-oxidation programs in combination with the continuous circulation of the chemicals and the thermostat for the developer ensure constant high image quality.

Microprocessor controlled with 2 program memory.

Digital display and control for developer temperature, replenishment, process time, diagnostics, and film counter.

Minimum Darkroom Requirements
• 115V, 50/60Hz, 12A Service (Operating Range 110-120V)
• 230V, 50/60Hz, 8.8A Service (Operating Range 220-240V)
• Energy use of 1.4kWh during processing and 0.12 kWh in standby mode.
• Dedicated line strongly recommended.
• Use of a multi-outlet adapter or extension cord will void the warranty.

• Cold water only with recommended temperature between 41-86oF (5-30oC).
• Water connection of 3/4" with 29 - 145 psi.
• Minimum drain diameter of 2 inches (5 cm) at a maximum of 12 inches (30.5 cm)above the floor.
• Water consumption of 0.5 gal/min (1.9 liter/min) during processing in standard mode.
• Water consumption of 0.25 gal/min (0.95 l/min) during processing in water save mode.
• Water consumption of 0.0 gal/min (0.0 l/min) in standby mode.
• In-line water filter strongly recommended when water supply contains contaminants or particulate materials.
• Do not use copper drain pipe or fittings. Use cast iron or PVC.

• Minimum counter/stand space of 19” (48 cm) wide by 23” (59 cm) deep required.
• Minimum counter clearance of 30" (77 cm) wide by 23" (59 cm) deep required.

• Film Size 4” x 4” (10 cm x 10 cm) min. to 14” (35 cm) X any length max. Will accept roll film.
• Processing Time Adjustable from 90 seconds to 10 minutes.
• Developer Temp Digital display in C or F, adjustable from 82 - 99F (28 - 37C).
• Replenishment Rates adjustable from 150-1500 ml per 10 sq. ft. (ml/m2. Level sensor in developer with overflow protection. Anti-oxidation cycle every hour (can be disabled)
• Net Weight 110 lbs (50 kg) with solutions, 77 lbs (35 kg) without solutions.
• Inner Tank Capacity 1.3 gallons (5 liter) in each section: developer, fixer, water.
• Film Drying by Warm circulated air, thermostat regulated and adjustable to 158F(70C) maximum
• Chemical Storage 6.6 gallon (25 L) tanks

Call for pricing and availability. 573-308-4448
Copyright 2000-2019